School Of Environment And Earth Sciences
Permanent URI for this communityhttps://kr.cup.edu.in/handle/32116/83
Browse
10 results
Search Results
Item Adsorption of Zn(II) on Pristine and SPLP/TCLP Leached Rice Straw Biochar: an Interplay of Precipitation and Ion Exchange(Institute for Ionics, 2022-11-15T00:00:00) Bhardwaj, Akanksha; Nag, Shilpa; Hussain, Khadim; Arora, Meenu; Pandey, Puneeta; Babu, J. NagendraThe inorganic mineral content in biochar influences the adsorption of Zn(II) metal ions. Metal ion adsorption on mineral rich rice straw biochar is influenced upon washing. Rice straw slow pyrolysis biochar BC1-3, respectively, prepared at 400, 500, and 600��C, were leached under Toxicity Characteristic Leaching Procedure (TCLP) and Synthetic Precipitation Leaching Procedure (SPLP) conditions to furnish BT1-3 and BS1-3, respectively. The Zn(II) adsorption studies were carried out for pH and dose optimization, initial concentration, isotherm fit, and kinetic studies. The Zn(II) adsorption by B(C/S/T)1�3 showed Langmuir and Freundlich isotherm, with pseudo-second-order kinetics at optimum pH 5 and dose 1�g/L. The adsorption of Zn(II) followed the trend BC3(qm 47�mg/g) > BC2 > BC1 > BS2 > BS1 > BS3 > BT2 > BT1 > BT3 (qm 3.5�mg/g), i.e., metal ion adsorption decreased with extent of leaching. The Zn(II) adsorption on biochar involved precipitation as dominant factor for metal ion adsorption on the biochars followed by ion exchange and proton exchange. The precipitation of Zn(II) ions in case of BC1-3 is attributed to the pH of biochar, which increases with proportion of minerals to organic content in biochar. In case of biochar BS1-3 and BT1-3, ion exchange and proton exchange mechanisms driven by demineralization are responsible for Zn(II) adsorption. The adsorption mechanism for Zn(II) on biochar is supported by XPS, solid state NMR studies. Graphical Abstract: [Figure not available: see fulltext.] � 2022, The Author(s), under exclusive licence to Springer Nature Switzerland AG.Item Effect of temperature and fly ash content on the catalytically pyrolyzed rice straw biochar�fly ash composites for methylene blue adsorption(John Wiley and Sons Ltd, 2022-09-26T00:00:00) Bhardwaj, Akanksha; Nag, Shilpa; Hussain, Khadim; Pandey, Puneeta; Babu, J. NagendraRice straw and fly ash are the wastes produced in abundance which need immediate attention for their management. In the present study, the in situ pyrolysis of rice straw in presence of fly ash was carried out and the resultant composites were studied for adsorption of methylene blue (MB). Slow pyrolysis of rice straw in presence of fly ash is evaluated using thermogravimetric analysis (TGA) and Coats�Redfern equation for pseudo-first-order reaction kinetics, respectively. The activation energy (Ea) for the pyrolysis of rice straw was 41.75 kJ/mol which was lowered to 37.39 kJ/mol in presence of fly ash. Biochar fly ash composites BFA41�3, BFA51�3, and BFA61�3 were prepared at three 400�C, 500�C, and 600�C pyrolysis temperature, respectively, the subscript indicating three different ratios of rice straw and fly ash (1:3, 1:1, and 3:1 w/w ratio). The composites BF4�61�3 were neutral to alkaline in pH, due to the presence of basic oxide and carbonates minerals. BFA4�61�3 was studied for batch adsorption of MB and optimized for pH, dose, and initial concentration of adsorbate. The maximum MB adsorption capacity of 25.91 mg/g was reported for the composite BFA41. MB adsorption efficiency (qe) followed the trend BFA41�3 > BFA51�3 > BFA61�3, which indicates a strong influence of biochar surface functional groups on dye adsorption, as reiterated by the multiple linear regression (MLR) analysis. Stripping of MB was achieved using methanol as a stripping agent for MB-adsorbed BFA4�61�3 with desorption efficiency of 7% to 11% in the first cycle and 23% to 100% in the second cycle. Thus, the biochar fly ash composite with optimum ion exchangeable functional organic moieties would be suitable for dye remediation and waste generated in the process could find application in soil amelioration. � 2022 Curtin University and John Wiley & Sons Ltd.Item Effect of Pyrolysis Temperature on Mechanistic Transformation for Adsorption of Methylene Blue on Leached Rice-Straw Biochar(John Wiley and Sons Inc, 2022-02-09T00:00:00) Bhardwaj, Akanksha; Nag, Shilpa; Dahiya, Amarjeet; Pandey, Puneeta; Arora, Meenu; Babu, J. NagendraToxicity characteristic leaching procedure (TCLP) leached biochar is studied for adsorption of methylene blue (MB). Rice straw biochar obtained from slow pyrolysis at 400, 500, and 600��C, respectively, is TCLP leached to furnish leached biochar, BL4, BL5, and BL6. The leached biochar BL4�6 have been characterized for pH, CHN analysis, ash, zeta potential, surface area morphology and functional groups. Batch adsorption studies are optimized for pH (3�9), adsorbent dose (0.5�4�g�L?1), and initial MB concentration (20�135�mg�L?1). Nonlinear fitting to Langmuir, Freundlich, and Redlich-Peterson adsorption isotherm with due statistical treatment and error function analysis is carried out. Leached biochar, BL4, BL5, and BL6, is characterized by the dominance of carboxylic acid, lactone, and phenols moieties, respectively. The MB adsorption on leached biochar exhibits maximum adsorption of 26.87, 51.34, and 18.83�mg�g?1 for BL4, BL5, and BL6, respectively. The underlying mechanism for adsorption of MB using BL5, is characterized by non-ionic lactone ring opening in presence of MB under alkaline conditions that is supported by X-ray photoelectron spectroscopy(XPS) and Fourier transformed infrared spectroscopy (FTIR) studies. Desorption of MB and regeneration from BL5 is studied with methanol and 0.1 m HCl as stripping solvent for four cycles. Recovery of MB is better with methanol in comparison to 0.1 m HCl. � 2022 Wiley-VCH GmbH.Item Removal of hexavalent chromium from aqueous solution using biomass derived fly ash from Waste-to- Energy power plant(Taylor & Francis, 2013) Vaid, Upma; Mittal, Sunil; Babu, J. NagendraFly ash from the agricultural waste-based Energy Power Plant has been studied for the adsorption of hexavalent chromium [Cr(VI)]. In order to maximize the Cr(VI) removal from simulated aqueous solutions, effects of various parameters i.e. adsorbent dose (10–40 g/L), contact time (5–90 min), variation in pH (1–5), and initial metal ion concentration (10–80 mg/L) on Cr(VI) adsorption were investigated by batch adsorption experiments. It was observed that adsorption of Cr(VI) on the selected adsorbent was dependent on pH. Before optimization of experimental conditions, the percent removal of Cr(VI) from the aqueous solution (10 mg Cr/L) was approximately 4%, which increased to approximately 99% after optimization of experimental conditions. Maximum adsorption was observed upon adding 10 g/L of adsorbent to a 60 mg Cr/L aqueous solution at pH 1.0 and contact time of 90 min at 200 rpm. Equilibrium adsorption data were well fitted in Langmuir isotherm model which substantiate monolayer adsorption of Cr(VI) on fly ash. Kinetics of Cr(VI) adsorption on fly ash follows pseudo-second-order reaction.Item Removal of hexavalent chromium from aqueous solution: a comparative study of cone biomass of “Picea smithiana” and activated charcoal(Taylor & Francis, 2016) Mittal, Sunil; Vaid, Upma; Najar, Gh Nabi; Babu, J. NagendraThe present work investigates comparative adsorption efficiency of powdered cone biomass of Picea smithiana (PCBP) and activated charcoal (AC) for removal of hexavalent chromium (Cr) (Cr(VI)) from aqueous solution. The study indicates that PCBP has 76% removal efficiency for Cr as compared to AC. Particle size and SEM-EDX analyses were done to determine average particle size, surface morphology and elemental composition of PCBP. BET and FTIR analysis were carried out to elucidate the adsorption mechanism of Cr(VI) on PCBP. Ashing has been proposed as a method for managing waste of loaded PCBP generated in adsorption. Ashing studies showed the ash content of PCBP to contribute only 13% of the ash generated from loaded biomass. Further, a comparative study has been made indicating the adsorption efficiency of PCBP with previously reported bio-waste materials. The results of this study show that PCBP has high adsorption efficiency as compared to other bio-waste materials.Item In situ reductive regeneration of zerovalent iron nanoparticles immobilized on cellulose for atom efficient Cr( VI ) adsorption(Royal Society of Chemistry, 2015) Sharma,Archana Kumari; Kumar,Rabindra; Mittal, Sunil; Hussain,Shamima; Arora, Meenu; Sharma, R.C.; Babu, J. NagendraZerovalent iron nanoparticles (nZVI) (11.8 ± 0.2% w/w) immobilized on microcrystalline cellulose (C-nZVI) were synthesized and studied for Cr(VI) sorption. The material showed good atom economy for Cr(VI) adsorption (562.8 mg g−1 of nZVI). Oxidation of cellulose to cellulose dialdehyde leads to in situ regeneration of nZVI which is responsible for the atom efficient Cr(VI) sorption by C-nZVI.Item Sorptive removal of arsenite [As(III)] and arsenate [As(V)] by fuller’s earth immobilized nanoscale zero-valent iron nanoparticles (F-nZVI): Effect of Fe 0 loading on adsorption activity(Elsevier, 2016) Sharma, Archana Kumari; Babu, J. Nagendra; Yadav,RadheshyamFuller’s earth immobilized nanoscale zerovalent iron (F-nZVI 1–8) were synthesized by borohydride reduction method. The iron loading of fuller’s earth immobilized nZVI was varied from 5 to 50% (w/w) in these F-nZVI 1–8. The F-nZVI 1–8 were characterized by FE-SEM–EDX, FTIR, BET, XRD and TGA. The FE-SEM analysis showed an increase in agglomeration of nZVI on the immobilized material with increase in the loading of Fe0. F-nZVI 1–8 were studied for adsorptive removal of As(III) and As(V) from aqueous solution, with an emphasis on the effect of Fe0 loading of adsorbent on arsenic remediation. Iron loading has a significant role in adsorption of As(III) and As(V) on F-nZVI, with increase in adsorption with optimum iron loading of 20% (w/w) on fuller’s earth (F-nZVI-4). However, increase in loading above 20%, resulted in no significant increase in As(III) and As(V) adsorption. The adsorption results fitted well with Langmuir and Freundlich isotherm models and the maximum adsorption capacity of F-nZVI-4 for As(III) and As(V) were observed to be 50.08 and 91.42 mg/g, respectively. The adsorption isotherm and kinetic studies indicate a rapid removal of As(III) and As(V) from the aqueous solution in the presence of F-nZVI 1-8, with an substantially high rate of removal for arsenic with F-nZVI-4.Item Multifaceted application of crop residue biochar as a tool for sustainable agriculture: An ecological perspective(Elsevier, 2015) Singh,Rishikesh; Babu, J. Nagendra; Kumar,Rabindra; Srivastava,Pratap; Singh, Pardeep; Raghubanshi,Akhilesh SinghLignocellulosic crop residue biomass, in surplus, is of vital importance due to its multifaceted utilization potential on- and off-site to agricultural systems; therefore, its management is essential for sustainable agriculture. The malpractice of open crop residue burning leading to the brown cloud phenomenon and contributing significantly to atmospheric heterogeneity through enhanced gaseous and particulate emissions is of greater off-late concern. Available traditional crop residue management (CRM) technologies have not achieved wider adaptation; therefore, recently thermochemical conversion has been foreseen as an interesting tool for potential CRM under changing climate scenario. Biochar, a by-product of thermochemical processes, has been evaluated as a potential soil ameliorant and C sequestration agent. As soil ameliorant, it improves soil basic properties directly along with subdued release of greenhouse gases from agroecosystems, provides adsorption surface to agrochemicals and improves essential nutrient dynamics. Since the potential benefits of biochar in soil are governed by initial pyrolysis conditions and soil types; therefore, its wider utilization potential as suitable tool in sustainable agriculture and climate change mitigation needs to be critically analyzed before its specific recommendation to an agroecosystem. The present review provides a critical insight on current research on various aspects, particularly ecological, of crop residue biochar starting from the feedstock sources, pyrolysis conditions and changes after application. Additionally, a brief account is given on the agronomic relevance and major constraints of biochar amendment as an ecological engineering tool for sustainable agriculture. After reviewing various aspects of crop residue as feedstock, we recommend its use as a blend, rather than sole use, along with several other lignocellulosic materials under pyrolysis process as well as ameliorating agent. ? 2015 Elsevier B.V.Item 1,3-Bis(cyanomethoxy)calix[4]arene capped CdSe quantum dots for the fluorogenic sensing of fluorene(Royal Society of Chemistry, 2017) Kumar, Rabindra; Arora, Meenu; Jain, A.K.; Babu, J. NagendraCapping of 1,3-bis(cyanomethoxy)-tert-butylcalix[4]arene (CAD) onto CdSe quantum dots (QDs) was characterized by a fluorescence enhancement of the QDs (?em = 580 nm) upon surface interaction with the phenolic moiety of CAD. CAD@QD showed selective and sensitive 1.67 fold fluorescence enhancement in the presence of fluorene among fifteen PAHs. The fluorescence enhancement was characterized by monolayer adsorption of fluorene on to the surface of CAD@QD. The limit of detection for fluorene was observed to be 0.8 nM. This method was used and compared with detection of fluorene in spiked respirable dust (PM10) samples collected during an open biomass (stubble) burning event. ? The Royal Society of Chemistry.Item Role of soil physicochemical characteristics on the present state of arsenic and its adsorption in alluvial soils of two agri-intensive region of Bathinda, Punjab, India(Springer Verlag, 2016) Kumar, Ravishankar; Kumar, Rabindra; Mittal, Sunil; Arora, Meenu; Babu, J. NagendraPurpose: Arsenic (As) contamination of groundwater has received significant attention recently in district Bathinda, due to consequent health risk in this region. Soil is the one of the primary medium for arsenic transport to groundwater. Thus, there is an essential requirement for understanding the retention capacity and mobility of arsenic in the soils to ensure sustainability of the groundwater in the locality. Arsenic interaction with various physicochemical properties of soil would provide a better understanding of its leaching from the soil. Materials and methods: Fifty-one soil samples were collected from two regions of Bathinda district with extensive agricultural practices, namely, Talwandi Sabo and Goniana. The soils were analyzed for arsenic content and related physicochemical characteristic of the soil which influence arsenic mobility in soil. Adsorption studies were carried out to identify the arsenic mobilization characteristic of the soil. SEM-EDX and sequential extraction of arsenic adsorbed soil samples affirmed the arsenic adsorption and its mobility in soil, respectively. Multiple regression models have been formulated for meaningful soil models for the prediction of arsenic transport behavior and understand the adsorption and mobilization of arsenic in the soil matrices. Results and discussion: Region-wise analysis showed elevated levels of arsenic in the soil samples from Goniana region (mean 9.58?mg?kg?1) as compared to Talwandi Sabo block (mean 3.38?mg?kg?1). Selected soil samples were studied for As(V) and As(III) adsorption behavior. The characteristic arsenic adsorption by these soil samples fitted well with Langmuir, Freundlich, Temkin, and D-R isotherm with a qmax in the range of 45 to 254?mg?kg?1 and 116 to 250?mg?kg?1 for As(III) and As(V), respectively. Adsorption isotherms indicate weak arsenic retention capacity of the soil, which is attributed to the sandy loam textured soil and excessive fertilizer usage in this region. PCM and MLR analysis of the soil arsenic content and its adsorption strongly correlated with soil physicochemical parameters, namely, Mn, Fe, total/available phosphorus, and organic matter. Conclusions: Manganese and iron content were firmly established for retention of arsenic in soil, whereas its mobility was influenced by organic matter and total/available phosphorus. The poor adsorptive characteristic of these soils is the primary cause of higher arsenic concentration in groundwater of this region. A strong correlation between monitored arsenic and adsorbed As(III) with manganese suggests As(III) as the predominant species present in soil environment in this region. ? 2015, Springer-Verlag Berlin Heidelberg.